HYDRAULIC IMPACT WRENCH ID07 CE

The ID07 is a high torque impact wrench used for tightening and loosening nuts and screwing lag bolts. It applies impact torque up to 500 ft-lb /675 Nm. Available with friction ring or bolt type retaining socket.

HYDRAULIC IMPACT WRENCH ID07

The ID07 is a high torque impact wrench used to adjust and loosen nuts and bolts. Apply a maximum impact torque of 675 Nm. Available with friction ring or bolt retainer sleeve.

90° LP SWIVEL

90 ° swivel elbow male thread UNF 3/8 "(LP) to female UNF 3/8" (LP). It enables optimal routing hoses.

IW24 HYDRAULIC IMPACT WRENCH

Stanley hydraulic impact wrenches for underwater applications are designed to meet the most stringent requirements for underwater screwing. Their rugged design includes an integrated motor and a rugged mechanism for the tough demands of railroad maintenance. The weight ratio -The power of this equipment has no comparison with an impact wrench of this type on the market.

ON/OFF REGULATOR VALVE LONG FLOWSTOP

On / off valve that opens or closes the air flow into the hose line where it is installed. It can be installed on any standard LP regulator hose. Approximate length: 7.8 cm

ON/OFF REGULATOR VALVE SHORT

On / off valve that opens or closes the air flow into the hose line where it is installed. Ideal to place on the second stage regulator due to its small size. Approximate length: 4.5 cm

VITON O-RINGS (14 Sizes)

O-rings box Viton 85 material shore A hardness, compatible with oxygen; with 14 different sizes and 10 units of each measure. 

WRIST WET NOTE

Underwater slate, with a special shape that fits to the wrist or forearm and allows place with other instruments without any disturb.

WET NOTE CORDURE COVER

TDS slate book with 40 waterproof pages and cordura cover with small pockets. Includes graphite pen attached with bungee to one edge of the cover. Allows writing in and out of the water.

WET NOTE

Indispensable for every diver, sailor or tourist. This waterproof notebook, is made of plastic sheets and designed to write underwater. The cover is of cordure.It has pockets for pens or compass and has an eye for a carabiner hook with double trigger.

S80 STAGE TANK HARNESS

Complete harness for mounting a side tank for stage, bailout or side mount. It is valid for aluminum cylinders used in technical diving of the S80 type. The set comes pre-assembled and requires minimal installation by the user, thus customizing the position of the tank.

S40 STAGE TANK HARNESS

Complete harness for mounting a side tank for stage, bailout or side mount. It is valid for aluminum cylinders used in technical diving of the S40 type. The set comes pre-assembled and requires minimal installation by the user, thus customizing the position of the tank.

ALUMINIUM TEK GOODMAN HANDLE ADJUSTABLE

TDS Goodman type handle made of lightweight anodized aluminum. The height of the handle is adjustable by means of a side screw with a wide knob, allowing it to be adjusted to the size of our hand and/or to the use with or without gloves. It is possible to adjust the height in immersion because it is not necessary to use a wrench.

SUBMERSIBLE PUMP SM20

The SM20 submersible pump is self-priming and can run dry without damage. It has the capacity to pump 250 gpm (946 lpm) and move solids up to 8 mm in diameter, making it an extremely powerful and reliable pump.

RIGHT TWIN VALVE CAP BLACK

Modular side Right-type valves cap, to close the side exit to exit manifold or modular plug. Matt black finish of the military series.

SUBMERSIBLE PUMP SM21

Stanley hydraulic pumps exemplify the sheer power of hydraulic tools. Our SM50 pump releases no less than 500 gallons per minute (1890 bpm) and its small size allows it to fit into an 11 inch deep by 10 inch square (26.7 cm x 25.4 cm) box.

LEFT TWIN VALVE CAP BLACK

Modular side Left-type valves cap, to close the side exit to exit manifold or modular plug. Matt black finish of the military series.

SUBMERSIBLE PUMP SM50

Stanley hydraulic pumps exemplify the sheer power of hydraulic tools. Our SM50 pump discharges no less than 500 gallons per minute (1890 lpm) and its small size allows it to fit into a box 11 inches deep by 10 inches square (26.7 cm x 25.4 cm).